Jeep Part Sales

1981-86 CJ7 4 CYL T4 OR T5; 1981-86 CJ7 4, 6 OR 8 CYL T170; REAR DRIVE SHAFT, Collapsed Length: 23" Alternate Part # 5362281 Learn More

Rough Country CV Drive Shaft Rear For 1994-95 Jeep Wrangler YJ (With 4" Lift) Learn More

The TeraFlex JT: 1.5” Rear Driveshaft Lowering Kit lowers the rear driveshaft center support mount to improve driveshaft angles during full droop. Learn More

Yukon Gear & Axle Heavy-Duty Driveshafts are engineered to be incredibly strong compared to stock Jeep CV shafts. Learn More

This double cardan style CV drive shaft is recommended for Jeep TJ Wrangler models equipped with 4in - 6in suspension lifts or 87-93 Jeep YJ Wrangler models equipped with 4in suspension lifts to prevent driveline vibration and the rear output shaft from breaking. Learn More

Installing the Teraflex High-Angle Rzeppa CV Rear Driveshaft on your Jeep Wrangler JK allows for greater angles than traditional U-joints. Learn More

1987-93 YJ Wrangler Up to 3" lift 20" extended and 16" collapsed Measure from the outer edge of the seal on the original transfer case tailhousing to the center of the differential yoke u-joint. This measurement will be the center to center u-joint measurement for the new drive shaft and should be between 19 and 21 long. CV drive shafts are specifically made for NP231 slip yoke eliminator kits. Shafts are made using quality Dana Spicer components. Slip spline is coated to prevent... Read More Learn More

Maximize your clearance and suspension flex in your 2-door Wrangler JK with a ICON Vehicle Dynamics Rear Driveshaft. Learn More

Maximize your clearance and suspension flex in your 4-door Wrangler Unlimited JK with a ICON Vehicle Dynamics Rear Driveshaft. Learn More

Take your Jeep Wrangler JL's off-road performance to greater heights with the Revolution Gear & Axle Rear 1310 CV Driveshaft. Learn More

Rough Country CV Drive Shaft Rear For 1997-06 Jeep Wranler TJ Non Rubicon (With 6cyl, Dana 35 & 44, 4" Lift -16.00) Learn More

Rough Country CV Drive Shaft Rear For 2003-06 Jeep Wrangler TJ Rubicon (With 4-6" Lift) Measurement: 16.875-inches - 20.125-inches (18.5 Running Length) Learn More

Rough Country CV Drive Shaft Rear For 2007-11 Jeep Wrangler JK 2 Door (With 3½-6" Lift) Collapsed Measurement: 23.875-inches Extended Measurement: 27.375-inches Learn More

Rough Country CV Drive Shaft Rear For 2012-18 Jeep Wrangler JK Unlimited 4-Door (With 3½-6" Lift) Measurement: 41.25-inches to 44.75-inches Learn More

1981 CJ5 4 OR 6 CYL SR4; 1982-86 CJ5 4 OR 6 CYL T4 OR T5; REAR DRIVE SHAFT, Collapsed Length: 13 ” Alternate Part # 5362276 Learn More

Rear Drive Shaft Slip Yoke for 87-95 Jeep® Wrangler YJ with Dana Style Shaft Alternate Part # 83502855 Learn More

Rear Driveshaft Assembly For 2001-05 Jeep Wrangler 2.5L 4 Cylinder Alternate Part # 52098784AC Learn More

Manufactured with top-quality components and workmanship. Painted, balanced and ready to install. Collapsed length of 16" Extended length of 18.25". Learn More

Yukon Gear & Axle Heavy-Duty Driveshafts are engineered to be incredibly strong compared to stock Jeep CV shafts. Learn More

Yukon Gear & Axle Heavy-Duty Driveshafts are engineered to be incredibly strong compared to stock Jeep CV shafts. Learn More

1997-06 TJ Wrangler Use only with slip-yoke eliminator kit. 2-6" of Lift 18" extended and 14" collapsed Reduce or eliminate driveline vibration with a CV-equipped drive shaft. Constant Velocity (CV) joints use two U-joints (double cardan style) in the place of a single U-joint. This smoothes out the driveline angle and reduces vibration due to extreme lifts or driveline changes. Learn More

New Rear Heavy Duty Jeep JK Wrangler Rubicon or Non Rubicon 1310 Series CV Driveshaft with Greasable U-joints Custom made by Adams Driveshaft. Learn More

Driveshaft Rear; 87-93 Jeep Wrangler YJ Learn More

1980 CJ7 4, 6 OR 8 CYL AUTO; 1981 CJ7 4 , 6 OR 8 CYL SR4; 1982-86 CJ7 6 CYL T4 OR T5; REAR DRIVE SHAFT, Collapsed Length: 20.75 ” Alternate Part # 5360987 Learn More

Rough Country CV Drive Shaft Rear For 2000-06 Jeep Wranler TJ Non Rubicon (With 6cyl, Dana 44, Manual Trans & 4" Lift -16.75) Learn More

Rough Country CV Drive Shaft Rear For 2007-11 Jeep Wrangler JK Unlimited 4 Door (With 3½-6" Lift) Learn More

Rough Country CV Drive Shaft Rear For 2012-18 Jeep Wrangler JK 2 Door (With 3½-6" Lift) Collapsed Measurement: 22.875-inches Extended Measurement: 26.375-inches Learn More

Rear Drive Shaft, 1987-96 XJ Cherokee 4.0L 4WD W/ AUTO TRANS AND D35 AXLE Alternate Part # 53003246 Learn More

Rear Driveshaft Assembly For 2003-06 Jeep Wrangler with Dana 35 And 4cyl Manual Alternate Part # 52853407AA Learn More

CJ REAR DRIVE SHAFTS 1976-79 CJ5 6 OR 8 CYL T150, Collapsed Length: 18.25 ” Alternate Part # 5356509 Learn More

This double cardan style CV drive shaft is recommended for Jeep XJ Cherokee models equipped with 4in - 6in suspension lifts to prevent driveline vibration and the rear output shaft from breaking. Learn More

Jeep Wrangler (JK) (2007-2011); 2-Door Model w/ 3.8L engine; w/ 42RLE Transmission; w/ NV241 Transfer Case; 1-Piece Rear Drive Shaft. Learn More

The Dana Spicer Rear 1350 Driveshaft is the upgrade that your Wrangler JL is looking for. This double-cardan style drive shaft increases the strength and ability of your AdvanTEK Dana 35 rear axle. Learn More

Yukon Gear & Axle OE-Style Driveshafts deliver superior performance over stock Jeep CV style shafts. For Jeep Wranglers with up to a 2 ½” lift. Learn More

Yukon Gear & Axle Heavy Duty Drive-Shafts deliver unbeatable performance over stock Jeep CV shafts. Learn More

Yukon Gear & Axle Heavy Duty Drive-Shafts deliver incredible performance over stock Jeep CV shafts. Learn More

This steel CV rear driveshaft from Rugged Ridge helps to reduce vibration and the driveline angle Learn More

Manufactured with top-quality components and workmanship. Balanced and ready to install. Learn More

New Rear Extreme Duty Jeep JK Wrangler Rubicon or Non Rubicon 1350 CV Driveshaft with Solid U-joints made by Adams Driveshaft. Learn More

New Rear Extreme Duty Jeep JK Wrangler Rubicon or Non Rubicon 1310 Series CV Driveshaft with Solid U-joints Custom made by Adams Driveshaft. Learn More

New Rear Extreme Duty Jeep JK Wrangler Rubicon or Non Rubicon 1310 Series CV Driveshaft with Solid U-joints Custom made by Adams Driveshaft. Learn More

This stock replacement rear driveshaft from Omix fits 1980 Jeep CJ7 with a SR4 or T170 manual transmission. Learn More

Driveshaft, Rear, 4sp Auto Trans Learn More

New Rear Extreme Duty Jeep JL Wrangler Rubicon - Sport - Sahara 1350 Series CV Driveshaft with Solid U-joints Custom made by Adams Driveshaft. Learn More

New Rear Extreme Duty Jeep JL Wrangler Rubicon - Sport - Sahara 1350 Series CV Driveshaft with Solid U-joints Custom made by Adams Driveshaft. Learn More

The Revolution Gear & Axle Rear 1350 CV Driveshaft allows you to run larger tires as well as a bigger lift for your Wrangler JL giving it unparalleled off-road performance. Learn More

Yukon Drive Shafts Fit 2018+ Jeep JL 4 Door Wranglers With Dana 35 (M200) Rear Axle Spicer 1310 U-Joint Size Is Suitable for Jeeps Running A Maximum Tire Size of 35" Ample Slip For Stock Wrangler Suspensions Up to 4 ½” lift, Long Arm Kits and Suspensions Over 4 ½” Will Have To Measure In Order to Verify Fitment. This Measures 45.25" from U-Joint to U-Joint Learn More

1997-06 TJ Wrangler Bare Steel Fits 3.5 - 6" lift for Mega Short SYE ONLY CV Style Custom designed drive shaft for use with our Mega Short Slip Yoke Eliminator kit. Works in combination with the Mega Short SYE on 97-06 Jeep Wranglers with a suspension lift of 3.5"to 6". Each of these double cardan CV style drive shafts replaces your single U joint drive shaft. Each drive shaft has been pre-balanced and has 3 zerk fittings for ease of lubricating. This ready to go drive shaft is a must... Read More Learn More

Jeep JK2 and JK4 Front and Rear Rebuild Kit 2007-18 Stock Jeeps use 1 Joint on the Front Driveshaft at the transfer case; 2 Joints on the Rear Driveshaft. Learn More

Rough Country CV Drive Shaft Rear For 1987-93 Jeep Wrangler YJ (With 6" Lift) Learn More

Rubicon Express Rear CV Driveshaft T-Case Adapter Flange 2007+ Jeep Wrangler JK 2 Door & Unlimited 4 Door Billet aluminum flange 8mm-1.25 x 25mm socket cap screws Rear transfer case flange adapter. Must be used with the following drive shaft part numbers: #RE1887-240 (2-door) and RE1887-430 (4-door). Learn More

1948-1971 Jeep CJ5 (CJ2a Serial # 13453 & Up) rear Drive Shaft 4 Cyl & 3 Speed Alternate Part # 906932 Learn More

You are buying a Rear XJ Cherokee 1310 [Extreme Duty Series] CV Driveshaft made by Adams Driveshaft the Industry Leader in Custom Driveshafts. Learn More

2007-15 JK Wrangler and Rubicon 2-Door Double-Cardan joint Direct bolt on drive shaft Extended Length = 22.50" Compressed Length = 26.50" 1310 U-joints New original equipment JK Wranglers use drive shafts that have Rzeppa CV joints similar to most front wheel drive cars. These CV joints are fine for normal car applications but when you lift your Jeep or put on larger tires and drive your Jeep off road, these joints are not up to the task! Rugged Ridge has developed a solution for this... Read More Learn More

Take your Jeep Wrangler JL's off-road performance to greater heights with the Revolution Gear & Axle Rear 1310 CV Driveshaft. Learn More

The RockJock® Driveshaft Carrier Bearing Drop Kit for Jeep JT Gladiators is mandatory in lifted applications to reduce driveline angles. Learn More

Getting the most from your JL Wrangler is as simple as upgrading your drive line. The Dana Spicer Rear 1350 Driveshaft is made for those Wrangler's with a factory or aftermarket AdvanTEK Dana 44 rear axle. Learn More

Yukon Gear & Axle OE-Style Driveshafts deliver unparalleled performance over stock Jeep CV shafts. For Jeep Wranglers with up to a 2 ½” lift. Learn More

1994-95 YJ Wrangler With up to 3" lift 20" extended and 16" collapsed Learn More

This double cardan style CV drive shaft is recommended for Jeep XJ Cherokee models equipped with 4in - 6in suspension lifts to prevent driveline vibration and the rear output shaft from breaking. Learn More

The Teraflex High-Angle Rzeppa CV Conversion Yoke allows you to convert U-joint style yokes to accept a Rzeppa style CV driveshaft. Learn More

Will only work on cut and tap flange style slip yoke eliminator 1310 series yoke Spicer drive shafts and components are as good as they get. This drive shaft is compatible with the RE1807, RE1801 Slip yoke eliminator kits and Currie Enterprises tail shaft conversion kits. Measurements are taken from flange face to center of the rear u-joint with the slip stub at the center of it's travel. measure your vehicle on the ground in the running position to get correct length. Fits These Vehicles:... Read More Learn More

New Rear Extreme Duty Jeep JK Wrangler Rubicon or Non Rubicon 1350 CV Driveshaft with Solid U-joints made by Adams Driveshaft. Learn More

You are buying a Rear TJ Non Rubicon 1310 [Extreme Duty Series] CV Driveshaft made by Adams Driveshaft the Industry Leader in Custom Driveshafts. Running Length 16.50" Learn More